
Default Login Password for Netgear WNR2000

All router models come with a set of default admin credentials. These credentials are usually the same for a specific brand or series of routers. You must use the default username and password to access your router’s interface for the first time. So, the default credentials are very important pieces of information regarding your router.
You must not keep using your default password for a long time after setting up your router. Instead, you should create a strong new admin password for your router to optimise its security.
The default password for the Netgear WNR2000 is “password”. Read on to know how to use it and other important information.
How to Use the Netgear WNR2000 for Admin Login?
You need the default gateway (IP address) and username apart from the password to access your router. So, you must find them first before proceeding with the admin login. Then, you can access your router’s web interface with a few simple steps.
- Find the Default Username and IP Address
You should find your router’s default credentials and IP address on a label on its back. Also, you can confirm the default password for your router using this label. Alternatively, you can also try finding out the default username and gateway from the router’s manual. You should find them on the internet if they are not on the service manual of your router.
Also, you must note that you need not necessarily use the default IP address for Netgear routers. Instead, you can simply enter “routerlogin.net” in the browser to access the login page.
- Set Up an Ethernet Connection with Your Router
You have to be connected to your router over an ethernet cable to access its admin interface. So, set up an ethernet connection between your computer and router to proceed with the login. You can easily access the router login page on your browser once you have a reliable connection. Also, you must note that you do not need an internet connection to access your router.
- Open the Admin Interface on Your Browser
Type the default IP address of your router into any web browser to open the login page. Then, enter the default username and password there to open your router’s web-based interface. You can then proceed with setting up your router if you have not done that already.
How to Customise Your Netgear WNR2000 Router’s Login Password?
You can change the password easily once you have accessed your router’s interface. So, log into your router’s interface with the aforementioned steps to customise its password. Then, proceed with one of the following methods to change the admin password for the interface:
- When You Have not yet Set Up the Router
Are you yet to set up your Netgear WNR2000? In that case, you can customise the admin password as a part of the setup process. Go to the Advanced tab on the admin interface and click on Setup Wizard. This will start the setup procedure, and you must configure various important settings on your router.
Your router will detect an internet connection first before asking you to create a new admin password. Enter the new password that you want to use when prompted. Create a strong password to optimise your router’s security before completing the rest of the setup procedure.
- After You have Set Up the Router
You can also change your Netgear router’s admin login password anytime after setting it up. All you need to do is log into the interface with the steps given earlier. Go to the Advanced tab, open the Administration settings, and click Set Password.
You must enter your existing password before creating a new one for your router. Then, type in the new password you want to use and enter it again on the other empty field to confirm it. Click on Apply once you are done to save the settings before logging out of the interface.
How to Reset Your Netgear WNR2000 Login Password?
As you probably know, the Enable Password Recovery feature can help you recover passwords if you forget them. However, you must turn on this feature before losing your password.
Is it disabled at the time you lose your password? In that case, a reset would be the only way to restore the default password on your router.
You cannot access your router unless you reset the password. Proceed with one of the following methods depending on which one applies to your case:
- If ‘Enable Password Recovery’ is Enabled
You need not restore the default login password if you had enabled the password recovery during the setup. Open any web browser and visit the MyNetgear portal to find the “Forgot Password?” option. Then, enter the email address linked to your Netgear account to proceed further.
Confirm your decision by clicking on Reset Password to receive a verification code in your email. Then, type in this code on the portal and create a new admin password for your router. Confirm your new password by entering it on both empty fields and clicking on Submit.
You should be able to access your router’s interface with the new password once done. Try it out once you are done with the password reset.
- Reset Your Router
Is the Enable Password Recovery option disabled on your Netgear router? If yes, you must reset the router to restore its default login password. Push and hold down the Reset button on the back panel for about 10 seconds to restore factory settings. This should restore the default password, which you must use to log in the next time.
Enter the admin username and password on the router login page after the reset. You should be able to access your router without any issues this time. If the login fails again, it probably indicates other problems with your router.
What if You Cannot log in with the Default Netgear WNR2000 Admin Password?
Various glitches with your router might cause login issues when you try to access its interface. Moreover, the problem might also have something to do with the ethernet connection.
Try out the following troubleshooting steps if your Netgear WNR2000’s default password is not working:
- Reboot the Router
You might fail to access your router’s interface due to various temporary errors in the device. Restarting the router should immediately fix such issues and resolve the login problems. Power cycle your router or turn it off for a minute before attempting to login again.
- Make Sure You have Entered the Password Correctly
As mentioned earlier, the default password for the Netgear WNR2000 is “password”. You must ensure you have entered it as it is given here. Also, you might want to confirm your router’s default password by the methods mentioned previously.
- Check whether Someone has Customised the Credentials
Your router might not have its default password if you cannot login. So, you must make sure whether someone has changed the password. Get the new password in case there is one and use it to access the router’s interface.
- Check the Ethernet Connection
You might fail to access your router’s interface due to a faulty ethernet connection. So, make sure the cable is inserted properly at both ends. Reconnect the cable to your computer and the router if that does not fix the problem. Also, you must consider using a different cable if the current one seems to be damaged.
You should be able to fix the ethernet connection with one of the aforementioned methods. If none of them is effective, there might be a problem with your device.
- Use a Different Device or Browser
Are you unable to access your router on a specific browser? In that case, you must simply switch to another browser and check whether that works. You must also consider switching to another device if that does not fix the problem. This can fix the issue effectively in many cases, depending on the cause of the login problems.
- Reset the Router
Your router might fail to let you log in due to a misconfiguration. In such cases, you might need to reset the device if restarting it does not do the trick. As we have seen, you can do that quite easily using the Reset button. After a reset, you can usually access your router with the default login password.
Conclusion
Finding your Netgear WNR2000 login password is quite easy. The information given here will hopefully make it easier for you to use this password. You must restore the default password whenever you fail to log in with the existing one. Replacing the router might be the only option if you cannot access it using the default credentials.